Main -> Hook -> How to Replace a Light Fixture With a Ceiling Fan . how-tos . DIY

How to Replace a Light Fixture With a Ceiling Fan . how-tos . DIY

Installing a Ceiling Fan - (White Hugger) 42" Middleton

You don't have to hire a handyman to install a ceiling fan. To connect your ceiling fan to existing wires, make sure that you have the right fan hardware and cut off the electricity leading to those wires. Mount your bracket onto the ceiling and hang the fan on the bracket. If you take your time and follow the correct steps, you can connect your ceiling fan wires by yourself! Once the power is off, read the instruction manual that came with the fan so you install everything correctly.

Find the short green wire or the green ground screw on your ceiling fan hanging bracket. Attach the bare copper wire from your electrical box to the short green wire by twisting and orange wire connector to the two wires. If you only have a green ground screw, wrap the bare copper wire around this screw and tighten the screw against the bracket to secure the wire.

Ceiling fans hook up

Match the end of the white insulated wire from the ceiling fan to the end of the white wire from your electrical box. Twist another wire connector onto the two wires to complete the neutral circuit.

Connect the black insulated wire from the ceiling fan to the black insulated wire from the electrical box. If you do not have a separate toggle switch on the wall to operate the ceiling fan and light separately, grab the blue wire and place it with the black wire from the fan motor and the black insulated wire from the electrical box.

Twist a yellow wire connector to all three wires. If you have the additional toggle switch, connect the two black wires together with an orange wire connector, and then match the blue wire and the red wire together. Twist another orange wire connector on the red and blue wires. Cecilia Harsch has been writing professionally since She writes mainly home improvement, health and travel articles for various online publications.

She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction. Harsch received her Certified Nurses Assistant license in If it is less than 12 feet, you'll need a fan that is inches in diameter. If the longest wall is 12 to 15 feet, get a inch fan. Anything over 15 feet, you'll need a inch fan.

You don't have to hire a handyman to install a ceiling fan. To connect your ceiling fan to existing wires, make sure that you have the right fan. Most of the time, the wires that fed a previous ceiling fan wiring light fixture are adequate for hooking up a new fan. If you have a ceiling fan wiring arrangement . If you had a red wire coming from your ceiling, it is hooked up to your wall switch. Fan: Black wire is for the fan. Blue wire is for the light, if light is included with the.

Chelsea Jackson. Photo By: Chelsea Jackson. If the room has no existing fixture, this project is more difficult and entails cutting through the ceiling and installing new wiring and a switch.

Cover the switch with tape to make sure it doesn't get turned back on while you are working Image 1. Use a circuit tester to ensure that the power is off before you touch any of the electrical wiring.

Disconnect the fixture wires and remove the central mounting nut and any screws that hold the old fixture in place. With the fixture out of the way, try to determine whether the electrical box is securely fastened to a ceiling joist or support bracket.

Fans can weigh up to 50 pounds and require a sturdy mount. If your ceiling box is enclosed by drywall or other material, you may need to access the joists from above, such as through the attic, to inspect it and attach a support brace if needed.

How to Wire a Ceiling Fan With a Light With Different Switches : Ceiling Fan Projects

Alternative installation methods are described below. If you have access from above, you can make and install your own support brace using a length of 2x4 lumber nailed to the ceiling joists on both sides of the box location Image 2.

Position the brace directly above the ceiling box. From below, use wood screws to attach the ceiling box securely to the brace. If you do not have access to work above the ceiling, you can install an expanding metal brace from below to support the ceiling box and fan.

First, remove the existing box, then insert the brace up through the hole and secure it in position by ratcheting the mechanism into place. As the ratchet is turned from below, arms on the brace extend until they contact the ceiling joists on both sides of the hole Image 3 demonstration.

The spikes on the arms anchor securely into the wood. Some braces are available with a ceiling box attached, or you can attach the existing ceiling box to the brace.

This method also may be used to mount a fan on a ceiling where no electrical fixture was previously installed.

After a hole is cut in the ceiling, electrical wiring is routed to the hole from a convenient nearby junction box, then the brace and a new ceiling box are installed as described above. Most ceiling fans come with a mounting bracket; if yours does not, you can buy a mounting kit separately.

Ceiling Fan Wiring. Hang The Ceiling Fan And Connect The Appropriate Wires. Lift the motor assembly. This can create some confusion when it comes to which wires to connect together . Many ceiling fans are designed to be used with or without a. Choose a ceiling fan light fixture, dedicated wiring i wired each color wire, we'll light can lights without spending time and. All about lights on most fans.

This bracket typically has a circular receptacle for a ball mount installed on the fan motor or extension rod. Because mounting a fan too close to the ceiling restricts air circulation, an extension rod of any length is generally recommended. If you use an extension rod to suspend the fan, temporarily tape the ends of the fan motor wiring together and pull the wiring through the rod. Attach the rod to the fan motor, and secure the ball mount at the upper end of the rod. Mount the fan motor to the ceiling bracket by inserting the swivel ball into the bracket.

If you don't know which switch controls your fan, turn on all the lights in your house. Once the lights are on, flip each switch until you switch off the power in the part of the house where the fan is located.

That switch most likely controls the power to your fan. Read the instruction manual that came with your fan. Some fan models have special warnings or instructions that you need to read before you start installing it.

Do It Yourself: Ceiling Fan Installation

Read the entire manual to make sure you're installing it correctly. Identify the individual wires coming out of your ceiling. There should be a white, copper or green, and black wire coming out of the ceiling's electrical box. Some setups will also have a blue wire, which powers the lights on your fan.

The white wire is your neutral wire, the copper wire is the grounded wire, and the black wire powers the fan. If you have a blue and black wire hanging out from your ceiling, you should also have 2 switches on your wall.

Examine the wires coming out of your fan.

Your fan should have a green, white, and black wire coming out of the top of it. If your fan also has a light, it will have a blue wire. There should also be a green grounding wire attached to the fan bracket itself. Screw the ceiling fan bracket into the ceiling. Thread the wires coming out of your ceiling through the center of the bracket so that they hang freely below it.

Place the screws that came with the bracket into the holes and turn them clockwise with a screwdriver to tighten them.

Learn more about Ceiling Fan installation procedure and Connect the grounding wires from downrod, ceiling and hanging bracket with a.

This should attach and secure the fan bracket to your ceiling. Hang the ceiling fan in the bracket. Slide the top of the ceiling fan into the groove in the bracket and hang it. Fans will have different setups and brackets, but all modern fans will allow you to hang the fan on the bracket so that you can connect the wires.

Strip the ends of the wires. To connect your wires, the copper ends must be exposed. Remove the plastic caps that are on the ends of your wires.

Use a stepladder to reach the wires in your ceiling and carefully cut away the plastic coating about 2 inches 5. Snip the plastic and slide it off to expose the copper wires. Repeat the process on the wires coming out of your fan. Twist both white wires together. The white wires are your neutral wires. Connect the white wire coming out of your ceiling to the white wire coming out of the top of the fan.

1 comments Add your comment below

Leave a Reply

Your email address will not be published. Required fields are marked *